２枚刃汎用エンドミル（Ｓ）
材質_______Ｃｏ−ＨＳＳ
ねじれ角___３０゜
特長_______太い柄径と最小の必要刃長を採用し切味と剛性にすぐれ、安定した切削が出来
ますので仕上精度も良好です。゜
直径の許容差゜
3mm以下 0〜-0.02
3.1mm以上 0〜-0.03
| 直径 | 刃長 | 全長 | 柄径 | 標準価格 | |
|---|---|---|---|---|---|
| B | O.5 | 0.8 | 50 | 6 | 4,190 |
| B | O.6 | 1 | 50 | 6 | 3,420 |
| B | O.7 | 1 | 50 | 6 | 3,420 |
| B | O.8 | 1.3 | 50 | 6 | 2,850 |
| B | O.9 | 1.3 | 50 | 6 | 2,850 |
| A | 1 | 2 | 50 | 6 | 2,190 |
| B | 1.1 | 2 | 50 | 6 | 2,850 |
| B | 1.2 | 2 | 50 | 6 | 2,850 |
| B | 1.3 | 2 | 50 | 6 | 2,850 |
| B | 1.4 | 2 | 50 | 6 | 2,850 |
| A | 1.5 | 3.5 | 50 | 6 | 1,990 |
| B | 1.6 | 3.5 | 50 | 6 | 2,580 |
| B | 1.7 | 3.5 | 50 | 6 | 2,580 |
| B | 1.8 | 3.5 | 50 | 6 | 2,580 |
| B | 1.9 | 3.5 | 50 | 6 | 2,580 |
| A | 2 | 5 | 50 | 6 | 1,880 |
| A | 2.5 | 6 | 50 | 6 | 1,850 |
| A | 3 | 8 | 50 | 6 | 1,630 |
| A | 3.5 | 8 | 60 | 8 | 1,630 |
| A | 4 | 8 | 60 | 8 | 1,630 |
| A | 4.5 | 10 | 60 | 8 | 1,630 |
| A | 5 | 10 | 60 | 8 | 1,630 |
| A | 5.5 | 12 | 60 | 8 | 1,630 |
| A | 6 | 12 | 60 | 8 | 1,630 |
| A | 6.5 | 15 | 65 | 10 | 1,790 |
| A | 7 | 15 | 65 | 10 | 1,790 |
| A | 7.5 | 15 | 65 | 10 | 1,790 |
| A | 8 | 15 | 65 | 10 | 1,790 |
| A | 8.5 | 20 | 75 | 10 | 2,080 |
| A | 9 | 20 | 75 | 10 | 2,080 |
| A | 9.5 | 20 | 75 | 12*10 | 2,080 |
| A | 10 | 20 | 75 | 12*10 | 2,080 |
| A | 11 | 22 | 85 | 12 | 2,670 |
| A | 12 | 22 | 85 | 12 | 2,670 |
| A | 13 | 26 | 90 | 12 | 3,310 |
| A | 14 | 26 | 90 | 16 | 3,310 |
| A | 15 | 26 | 100 | 16 | 3,690 |
| A | 16 | 32 | 100 | 16 | 3,980 |
| A | 17 | 32 | 100 | 16 | 4,770 |
| A | 18 | 32 | 100 | 16 | 4,770 |
| A | 19 | 32 | 115 | 20 | 5,730 |
| A | 20 | 38 | 115 | 20 | 5,730 |