ＫＨＡ（粉末ハイス）
２枚刃ＫＨＡエンドミル（Ｓ）
材質_______ＫＨＡ
ねじれ角___３０゜
特長_______２ＳＳシリーズの２枚刃汎用エンドミル（Ｓ）よりさらに重切削、高硬度難削材切
削に適したＫＨＡ（粉末ハイス）シリーズです。
直径の許容差
3mm以下 0〜-0.02
20mm以下 0〜-0.03
21mm以上 0〜-0.04
| 直径 | 刃長 | 全長 | 柄径 | 標準価格 | |
|---|---|---|---|---|---|
| A | 1 | 2 | 50 | 6 | 3,060 |
| A | 1.5 | 3.5 | 50 | 6 | 2,780 |
| A | 2 | 5 | 50 | 6 | 2,630 |
| A | 2.5 | 6 | 50 | 6 | 2,580 |
| A | 3 | 8 | 50 | 6 | 2,220 |
| A | 3.5 | 8 | 60 | 8 | 2,220 |
| A | 4 | 8 | 60 | 8 | 2,220 |
| A | 4.5 | 10 | 60 | 8 | 2,220 |
| A | 5 | 10 | 60 | 8 | 2,220 |
| A | 5.5 | 12 | 60 | 8 | 2,220 |
| A | 6 | 12 | 60 | 8 | 2,220 |
| A | 6.5 | 15 | 65 | 10 | 2,420 |
| A | 7 | 15 | 65 | 10 | 2,420 |
| A | 7.5 | 15 | 65 | 10 | 2,420 |
| A | 8 | 15 | 65 | 10 | 2,420 |
| A | 8.5 | 20 | 75 | 10 | 2,800 |
| A | 9 | 20 | 75 | 10 | 2,800 |
| A | 9.5 | 20 | 75 | 12 | 2,800 |
| A | 10 | 20 | 75 | 12 | 2,800 |
| A | 11 | 22 | 85 | 12 | 3,580 |
| A | 12 | 22 | 85 | 12 | 3,580 |
| A | 13 | 26 | 90 | 12 | 4,460 |
| A | 14 | 26 | 90 | 16 | 4,460 |
| A | 15 | 30 | 100 | 16 | 4,980 |
| A | 16 | 32 | 100 | 16 | 5,350 |
| A | 17 | 34 | 100 | 16 | 6,400 |
| A | 18 | 34 | 100 | 16 | 6,400 |
| A | 19 | 38 | 115 | 20 | 7,690 |
| A | 20 | 38 | 115 | 20 | 7,690 |
| B | 21 | 45 | 115 | 20 | 9,320 |
| B | 22 | 45 | 115 | 20 | 10,800 |
| B | 23 | 50 | 120 | 25 | 10,800 |
| B | 24 | 50 | 120 | 25 | 10,800 |
| A | 25 | 50 | 120 | 25 | 10,800 |
| B | 26 | 50 | 120 | 25 | 12,000 |
| B | 27 | 55 | 125 | 25 | 14,300 |
| B | 28 | 55 | 125 | 25 | 14,300 |
| B | 29 | 55 | 125 | 25 | 17,200 |
| A | 30 | 55 | 125 | 25 | 17,200 |
| A | 35 | 60 | 145 | 32 | 26,600 |
| A | 40 | 65 | 150 | 32 | 37,700 |
| B | 45 | 70 | 155 | 42 | 55,200 |
| B | 50 | 70 | 150 | 42 | 66,300 |